Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Stellt Eure Planungen & Eigenbauten vor ...
Willhelm B.
Beiträge: 497
Registriert: 28.08.2017, 14:33

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von Willhelm B. » 04.01.2020, 14:16

Welche Verdrahtung ist denn zu bevorzugen, wenn man beide Möglichkeiten hat.
Also Common Anode oder Common Cathode?

ich habe common cathode also gemeinsames GND. Ich weis aber nicht ob das optimal ist. Es scheint aber zu funktionieren. Controller ist ein MK3/9 von Planet-CNC
Oder ist das in diesem fall egal?

Gruß Willi

millhouse_
Beiträge: 328
Registriert: 31.10.2018, 09:06

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von millhouse_ » 04.01.2020, 16:56

ISE 14.7 müsste das gewesen sein. Die letzte ISE Version.


@Wilhelm
Bei mir lief nur die hier gezeigte. Mit - an gnd und + an den Steuerpins hat der Motor gar nix gemacht. Ansonsten kann ich dir da auch nicht weiterhelfen. Solange es läuft passts.

Willhelm B.
Beiträge: 497
Registriert: 28.08.2017, 14:33

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von Willhelm B. » 04.01.2020, 18:49

Danke. Es ist nur eine Frage die mir schon lange im Kopf liegt.

Gruß
Willi

millhouse_
Beiträge: 328
Registriert: 31.10.2018, 09:06

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von millhouse_ » 05.01.2020, 17:18

@Wilhelm

Hatte ganz vergessen dass mir das jemand in der cnczone mal erklärt hat:


https://www.cnczone.com/forums/stepper- ... e-use.html
it will be better to wire the common connection to the DQ542MA inputs to to the BOB's +5V (pul+,dir+,enbl+ commoned to +5V )

as the BOB's NPN outputs can sink more current to 0V / ground
than the 1K pull up resistors can provide if you wire the stepper driver inputs to a common ground
the current through the stepper drivers input opto-isolator LED's will be limited by the 270 ohm resistor inside of the stepper driver and the 1K pullup resistors on the breakout board
this will reduce the LED current to about 2.3mA
( instead of 10mA when the DQ542MA inputs are connected to a common +5V)

Könnte erklären warum es mit + an den Steuerpins bei dem BOB nicht funktioniert hat.

Das hängt aber von verwendeten Breakoutboard ab. In dem Fall bezieht sich die Antwort auf das China 1205 BOB.

other breakout boards that have the outputs of IC's like the 74245 connected directly to the stepper driver inputs
are able to work equally well with both ways of wiring the BOB to the stepper driver

the 74245 IC's can source about 35mA from the +5V supply or sink about 35mA to 0V / ground

Auf deutsch. Das 1205 BOB kann mehr Strom über gnd abführen als es an den Pins liefern kann.

millhouse_
Beiträge: 328
Registriert: 31.10.2018, 09:06

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von millhouse_ » 06.01.2020, 23:16

In den nächsten Tagen wird die X Achse endlich ausgerichtet. Da das Portal etwas schräg steht ( rechts vll. 0.2mm höher als links ) muss leider auch die KUS der X Achse etwas schräg stehen. Der Winkel von KUS zu Motor wäre laut Rechner um die 0,015°. Geht das mit den Wellenkupplungen? Es sind die mit rotem Kunststoffstern.

millhouse_
Beiträge: 328
Registriert: 31.10.2018, 09:06

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von millhouse_ » 08.01.2020, 15:44

Kurzes Update:

Heute kamen 6 Alurohre. Jeweils 40mm Durchmesser, 4mm Wandstärke. Eigentlich sollten die Teile in die Profile gepresst werden... In den 80x80 Profilen wackeln sie rum und in die 160x80 Profile wird man die nur mit einer bösen Presse bekommen. Hab versucht eins reinzubekommen. Nach 3cm war dann definitiv Schluß. Das Ding wieder rauszubekommen war grad nochmal ein Drama.

So wie sich die Profilkanten ins Rohr gefressen haben wird es nicht sinnvoll sein die mit Gewalt reinzudrücken.

Fazit: Gut gemeint aber definitiv nein.

Willhelm B.
Beiträge: 497
Registriert: 28.08.2017, 14:33

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von Willhelm B. » 08.01.2020, 17:41

und in epoxy einlegen?

millhouse_
Beiträge: 328
Registriert: 31.10.2018, 09:06

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von millhouse_ » 08.01.2020, 19:20

Das würde für die zwei 80x80 Profile gehen. Aber die eigentlichen Profile der Y Achse sind im innern zu untermaßig.


So sah das aus beim Versuch das Teil reinzuklopfen:

2020-01-08 19.17.47.jpg

AE-CNC
Beiträge: 69
Registriert: 28.03.2019, 18:57

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von AE-CNC » 09.01.2020, 09:11

Für welchen Zweck willst du die Alu-Rohre in die Profile einfügen?

millhouse_
Beiträge: 328
Registriert: 31.10.2018, 09:06

Re: Katatonische Rennsau.. Hobby CNC aus Aluminium/-profilen

Beitrag von millhouse_ » 09.01.2020, 12:20

Um das ganze n bisschen stabiler und schwingungsärmer zu machen sollten die Rohre rein und dann rechts und links noch dünne Aluplatten auf die Profilseiten.

Antworten

Wer ist online?

Mitglieder in diesem Forum: 0 Mitglieder und 23 Gäste